[UPDATED] NACE NACE-CIP1-001 Certification Exam Questions
Quickly and Easily Pass NACE Exam with NACE-CIP1-001 real Dumps
NACE NACE-CIP1-001 (Coating Inspector Level 1) Certification Exam is a comprehensive exam that assesses the knowledge and skills of individuals seeking a career in the coating inspection industry. NACE-CIP1-001 exam is designed to test the proficiency of the candidates in the areas of surface preparation, coating application, inspection techniques, and safety protocols. Passing NACE-CIP1-001 exam is a great achievement for individuals who want to enter the coating inspection profession and advance their careers.
NEW QUESTION # 55
Stripe coats are generally applied to:
- A. a), b), and c)
- B. Complex geometric shapes
- C. Welds
- D. Edges and corners
Answer: A
NEW QUESTION # 56
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 105 Gauge Readings resulting in 35 Spot Measurements
- B. 75 Gauge Readings resulting in 25 Spot Measurements
- C. 225 Gauge Readings resulting in 75 Spot Measurements
- D. 45 Gauge readings resulting in 15 Spot Measurements
Answer: C
NEW QUESTION # 57
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to the air temperature.
- C. a measure of the amount of moisture in the air compared to saturation level.
- D. the highest temperature at which moisture forms on a steel surface.
Answer: C
NEW QUESTION # 58
To be of value the Inspector's documentation must be:
- A. Timely, accurate and concise
- B. Always typewritten
- C. Always handwritten
- D. Submitted before the end of the job
Answer: A
NEW QUESTION # 59
Prior to using Inspection Tools the inspector must:
- A. Ensure the instrument is within calibration parameters
- B. a), b) & c)
- C. Read the manufactures' instructions
- D. Be trained on how to use the instrument
Answer: B
NEW QUESTION # 60
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. transitioning.
- B. juxtaposing.
- C. monitoring
- D. telegraphing.
Answer: D
NEW QUESTION # 61
The NACE Inspector should perform tests for soluble salts:
- A. After surface preparation
- B. When specified
- C. Prior to coating application
- D. Prior to surface preparation
Answer: B
NEW QUESTION # 62
ISO SA 3 is directly equivalent to:
- A. None of the above
- B. NACE No. 3/SSPC SP 6
- C. NACE No. 1/SSPC SP 5
- D. NACE No. 2/SSPC SP 10
Answer: A
NEW QUESTION # 63
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. brush-off blast cleaning.
- B. commercial blast cleaning.
- C. white metal blast cleaning.
- D. near-white metal blast cleaning.
Answer: A
NEW QUESTION # 64
Dew point is the temperature at which
- A. humidity decreases
- B. the air is saturated.
- C. water freezes.
- D. condensation occurs.
Answer: D
NEW QUESTION # 65
Whenever dissimilar metals must join, the most common practice is to
- A. coat all connected dissimilar metals.
- B. avoid coating all connected dissimilar metals.
- C. provide cathodic protection to prevent corrosion,
- D. provide anodic protection to prevent corrosion.
Answer: A
NEW QUESTION # 66
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Airless spray equipment
- B. Hand tools
- C. Abrasive blast nozzles
- D. Power tools
Answer: D
NEW QUESTION # 67
Which one of these elements is not necessary for corrosion to occur:
- A. Anode
- B. Reference Cell
- C. Electrolyte
- D. Cathode
Answer: B
NEW QUESTION # 68
ISO ST 3 is described as:
- A. Very Thorough hand or power tool cleaning
- B. Thorough blast cleaning
- C. Very Thorough power tool cleaning
- D. Thorough hand tool cleaning
Answer: A
NEW QUESTION # 69
Inspector's daily reports are used:
Select All That Apply
- A. To help in cases of a coating failure
- B. By the contractor to estimate the amount of work done that day
- C. To aid in arbitration between the contractor and client
- D. To provide continuity between inspectors
Answer: A,B,C,D
NEW QUESTION # 70
What is used to determine compressed air cleanliness?
- A. Psychrometer
- B. Blotter test
- C. Profilometer
- D. Needle pressure gauge
Answer: C
NEW QUESTION # 71
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Permit coating to take place so as not to lose the blast
- C. Review the relevant standard with the Contractor
- D. Shut the job down
Answer: C
NEW QUESTION # 72
Osmotic blistering is most likely to occur as a result of
- A. airless spray application
- B. inadequate anchor pattern/surface profile.
- C. overcoating a surface contaminated with chemical salts.
- D. applying tine coating too thin.
Answer: A
NEW QUESTION # 73
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Hire a third patty to assist you in understanding the document
- B. Carefully review the document and do the best you can
- C. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- D. Advise the owners' representative of your lack of knowledge in this area
Answer: B
NEW QUESTION # 74
Which of these tests uses a syringe?
- A. Soluble salts meter
- B. Potassium ferricyanide
- C. Sleeve test
- D. Bresle patch
Answer: D
NEW QUESTION # 75
Checking is
- A. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- B. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- C. an exposed area of the substrate or previous coat material, caused by poor application technique.
- D. a fine crack in the surface of a coating that rarely reaches the substrate
Answer: D
NEW QUESTION # 76
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. observe and report the quality of the work performed.
- C. direct and perform the work stated in the specification.
- D. observe and direct the work of the contractors.
Answer: B
NEW QUESTION # 77
An inspectors personal log book should contain:
- A. No comments regarding the application team
- B. The inspector's personal opinions of the application team
- C. Objective comments regarding the application work
- D. Subjective comments re ding the application team
Answer: A
NEW QUESTION # 78
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Break the blisters to see what's inside
- B. Document the problem and advise the Contractor
- C. Document the problem and advise the Contractor and Owner's representative
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: C
NEW QUESTION # 79
......
Start your NACE-CIP1-001 Exam Questions Preparation: https://www.pass4sures.top/CIP-Level-1/NACE-CIP1-001-testking-braindumps.html
Realistic NACE-CIP1-001 Dumps Questions To Gain Brilliant Result: https://drive.google.com/open?id=11IVQdcRX0IBJOerENh8SPzbJZamb2VW8