Get instant access to NACE-CIP1-001 Practice Tests 2021 Free Updated Today!
Welcome to download the newest PassLeader NACE-CIP1-001 PDF dumps ( 100 Q&As)
NEW QUESTION 30
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Anode
- C. Reference Cell
- D. Cathode
Answer: C
NEW QUESTION 31
Relative humidity is
- A. the highest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. a measure of the amount of moisture in the air compared to the air temperature.
- D. the lowest temperature at which moisture forms on a steel surface.
Answer: B
NEW QUESTION 32
To achieve consistently accurate results with ALL alt test equipment
- A. wear gloves when sampling.
- B. calibrate the instrument in the field.
- C. wash your hands before sampling.
- D. avoid placing the sample discs on a surface.
Answer: C
NEW QUESTION 33
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. Low Surface Temperature
- C. Low Relative Humidity
- D. High Surface Temperature
Answer: C
NEW QUESTION 34
Daily reports are important because:
Select All That Apply
- A. Management uses them to make personnel decisions.
- B. The information aids communication with supervisors.
- C. Inspectors rarely change on a project.
- D. the information impacts future projects.
Answer: A,B,D
NEW QUESTION 35
ISO SA 2 is defined as:
- A. Very Thorough Blast Cleaning
- B. Thorough Blast Cleaning
- C. Near White Metal Blasting
- D. Light Blast Cleaning
Answer: B
NEW QUESTION 36
NACE SP 0178 is a standard for:
- A. Structural steel to be coated for Atmospheric Service
- B. Stainless steel pipe to be Externally Coated
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Tanks and Vessels to be Externally Coated
Answer: C
NEW QUESTION 37
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the more aggressive profile
- B. Record the segment with the less aggressive profile
- C. Use another method as the comparator method is too subjective
- D. Record your result by identifying two segments
Answer: B
NEW QUESTION 38
ISO SA 3 is directly equivalent to:
- A. NACE No. 2/SSPC SP 10
- B. NACE No. 1/SSPC SP 5
- C. None of the above
- D. NACE No. 3/SSPC SP 6
Answer: C
NEW QUESTION 39
Upon arrival of coating materials, the inspector should
- A. observe and document the amount of material and batch numbers.
- B. observe aryl document that the applicator WFT at regular intervals during application.
- C. observe and document time frame and environmental conditions between each coat.
- D. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
Answer: A
NEW QUESTION 40
Non Conformance Reports are completed by the Inspector:
- A. In accordance with the specification's definition of a non-conformance
- B. In every instance that an item does not meet the specification requirements
- C. When the Inspector deems it to be a significant non-conforming item
- D. When the Inspector and Contractor deem it to be a significant non-conforming item
Answer: D
NEW QUESTION 41
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Call your supervisor
- C. Advise the Contractor he can proceed
- D. Advise the Contractor he cannot proceed
Answer: A
NEW QUESTION 42
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Never change his/her mind
- B. Call the supervisor
- C. Go with the majority opinion
- D. Achieve consensus through negotiation
Answer: B
NEW QUESTION 43
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Call the coating manufacturer for clarification
- B. Call the person who wrote the specification for clarification
- C. Use the product data sheet as a guide
- D. Use the job specification as a guide
Answer: D
NEW QUESTION 44
ASTM Standards are applicable:
- A. When specified
- B. In Asia
- C. In North America
- D. In the USA
Answer: A
NEW QUESTION 45
......
Sep-2021 Latest Pass4sures NACE-CIP1-001 Exam Dumps with PDF and Exam Engine: https://www.pass4sures.top/CIP-Level-1/NACE-CIP1-001-testking-braindumps.html
Premium Quality NACE NACE-CIP1-001 Online dumps: https://drive.google.com/open?id=1a7ZaGPIgGRqy0RPz2fpG5h1bccf_SSEX