Pass Your 300-410 Exam Easily With 100% Exam Passing Guarantee [2024]
300-410 Dumps are Available for Instant Access from Pass4sures
Cisco 300-410: Implementing Cisco Enterprise Advanced Routing and Services (ENARSI) exam is a comprehensive test that evaluates the knowledge and skills of network professionals in advanced routing and services. 300-410 exam consists of multiple-choice questions, drag-and-drop questions, and simulations, and is designed to test the candidate's ability to apply their knowledge in practical situations.
NEW QUESTION # 24 
Refer to the exhibit. The R1 routing table has the prefixes for the FTP1 and FTP2 file servers. A network engineer must configure the R1 with these requirements:
* Host1 must use the FTP1 fileserver.
* Host2 must use the FTP2 fileserver.
Which configuration meets the requirement on R1?
- A.
- B.
- C.
- D.
Answer: D
NEW QUESTION # 25
Refer to the exhibit.
Which action resolves the adjacency issue?
- A. Configure the same EIGRP process IDs.
- B. Match the hello interval timers.
- C. Configure the same autonomous system numbers.
- D. Match the authentication keys.
Answer: C
NEW QUESTION # 26
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
Answer:
Explanation:
NEW QUESTION # 27 
Refer to the exhibit. A network administrator configured NTP on a Cisco router to get synchronized time for system and logs from a unified time source The configuration did not work as desired Which service must be enabled to resolve the issue?
- A. Enter the service timestamps log datetime console global command.
- B. Enter the service timestamps log datetime synchronize global command.
- C. Enter the service timestamps log datetime localtime global command.
- D. Enter the service timestamps log datetime clock-period global command
Answer: C
Explanation:
Explanation
If a router is configured to get the time from a Network Time Protocol (NTP) server, the times in the router's log entries may be different from the time on the systemclock if the [localtime] option is not in the service timestamps log command. To solve this issue, add the [localtime] option to the service timestamps log command. Thetimes should now be synchronized between the system clock and the log message timestamps.
NEW QUESTION # 28
Refer to the exhibit.
After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)
- A. Change the mode from mode tunnel to mode transport on R3.
- B. Configure the crypto isakmp key cisco address 192.1.1.1 on R2 and R3.
- C. Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3.
- D. Remove the crypto isakmp key cisco address 10.1.1.1 on R2 and R3.
- E. Change the mode from mode transport to mode tunnel on R2.
Answer: A,C
NEW QUESTION # 29
An engineer configured a DHCP server for Cisco IP phones to download its configuration from a TFTP server, but the IP phones failed to toad the configuration What must be configured to resolve the issue?
- A. BOOTP port 67
- B. DHCP option 66
- C. DHCP option 69
- D. BOOTP port 68
Answer: B
Explanation:
NEW QUESTION # 30
Refer to the exhibit. The remote server is failing to receive the NetFlow data Which action resolves the issue?
- A. Modify the interlace command to Ip flow monitor FLOW-MONITOR-1 Input.
- B. Modify the flow transport command transport udp 2055 to move under flow monitor profile.
- C. Modify the udp port under flow exporter profile to Ip transport udp 4739.
- D. Modify the flow record command record v4_r1 to move under flow exporter profile.
Answer: A
Explanation:
From the exhibit we see there are two flow monitors: the first one "FLOW-MONITOR-1" has been configured correctly but the second one "v4_r1" was left empty andinterface E0/0.1 is using it. So the remote server does not receive any NetFlow data.
NEW QUESTION # 31
An engineer configured access list NON-CISCO in a policy to influence routes
What are the two effects of this route map configuration? (Choose two.)
- A. Packets are forwarded using normal route lookup.
- B. Packets are not evaluated by sequence 10.
- C. Packets are dropped by the access list.
- D. Packets are forwarded to the default gateway.
- E. Packets are evaluated by sequence 10.
Answer: D,E
Explanation:
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/ip-routed-protocols/47121-pbr-cmds-ce.html
NEW QUESTION # 32
Refer to the exhibit.
R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to
172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
- A. In route reflector setups, prefixes are not advertised from one client to another.
- B. R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
- C. Route reflector setup requires full IBGP mesh between the routers.
- D. In route reflector setup, only classful prefixes are advertised to other clients.
Answer: B
NEW QUESTION # 33
Refer to the exhibit.
An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?
- A. Configure the logging clock synchronize command in global configuration mode.
- B. Make sure that the clock on the device is synchronized with an NTP server.
- C. Configure the service timestamps log datetime localtime command in global configuration mode.
- D. Configure the service timestamps log uptime command in global configuration mode.
Answer: B
NEW QUESTION # 34
Refer to the exhibit.
Refer to the exhibit. The administrator is troubleshooting a BGP peering between PE1 and PE3 that is unable to establish Which action resolves the issue?
- A. Remove the traffic filtering rules on P2 blocking the BGP communication between PE1 and PE3
- B. Disable sending ICMP unreachables on P2 to allow PE1 to establish a session with PE3
- C. Ensure that the PE3 loopback address is used as a source for BGP peering to PE1
- D. P2 must have a route to PE3 to establish a BGP session to PE1
Answer: C
NEW QUESTION # 35
A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?
- A. clock calendar-valid
- B. service timestamps log datetime localtime show-timezone
- C. service timestamps log uptime
- D. clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00
Answer: B
Explanation:
By default, Catalyst switches add a simple uptime timestamp to logging messages. This is a cumulative counter that shows the hours, minutes, and seconds since the switch has been booted up
NEW QUESTION # 36 
Refer to the exhibit. Your company's security policy requires you to allow telnet access using tcp port 3033 only.
You apply the configuration changes as shown and then test. Your telnet attempt fails. Which action would correct the issue?
- A. remove transport input telnet from the VTY lines
- B. add access-list 101 deny tcp any any eq 23 to the ACL
- C. add rotary 33 to the VTY lines
- D. remove authorization exec ITCC from the VTY lines
Answer: A
Explanation:
Explanation
NEW QUESTION # 37
What are two MPLS label characteristics? (Choose two.)
- A. The label edge router swaps labels on the received packets.
- B. Labels are imposed in packets after the Layer 3 header.
- C. LDP uses TCP for reliable delivery of information.
- D. An MPLS label is a short identifier that identifies a forwarding equivalence class.
- E. A maximum of two labels can be imposed on an MPLS packet.
Answer: C,D
Explanation:
Reference:
https://www.cisco.com/c/en/us/support/docs/multiprotocol-label-switching-mpls/mpls/4649-mpls-faq-4649.html
NEW QUESTION # 38 
Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server RouterB is configured as follows:
Interface fastethernet 0/0
description Client DHCP ID 394482431
Ip address 172 31 11 255 255.255 0
!
ip route 172.16.1.0 255 255 255.0 10.1.1.2
Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?
- A. RouterBiconfig-ififclp helper-address 255.255 255 255
- B. RouterB(config-if)#lp helper-address 172.16.1.2
- C. RouterB(config-if)#lp helper-address 172.31.1.1
- D. RouterB(config-if)#lp helper-address 172.16.1.1
Answer: B
NEW QUESTION # 39 
Refer to the exhibit. The company implemented uRPF to address an antispoofing attack. A network engineer received a call from the IT security department that the regional data center is under an IP attack Which configuration must be implemented on R1 to resolve this issue?
- A. Option D
- B. Option B
- C. Option C
- D. Option A
Answer: B
NEW QUESTION # 40
Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.
Answer:
Explanation:
Explanation
HTTP and HTTPs run on TCP port 80 and 443, respectively and we have to remember them.
Syslog runs on UDP port 514 while NTP runs on UDP port 123 so if we remember them we can find out the matching answers easily. But maybe there is some typos in this question as 2001:d88:800:200c::c/126 only ranges from 2001:d88:800:200c:0:0:0:c to 2001:d88:800:200c:0:0:0:f (4 hosts in total). It does not cover host
2001:0D88:0800:200c::1f. Same for 2001:D88:800:200c::e/126, which also ranges from
2001:d88:800:200c:0:0:0:c to 2001:d88:800:200c:0:0:0:f and does not cover host 2001:0D88:0800:200c::1c.
NEW QUESTION # 41
......
You can read the Best Solution to prepare Cisco Certified Specialist - Enterprise Advanced Infrastructure Implementation (300-410) Exam
If you are preparing for CCENT certification, then Cisco 300-410 exam dumps is the perfect solution for you. It will help you to understand the basic networking knowledge required for the preparation of CCENT certification exam. Practice questions for CCENT exam help you to understand the topics. Major topics covered by Cisco CCENT certification are networking. Leaders in online instruction for the preparation of CCENT exam is available for you. Sample exam of CCENT certification is available for you. Studying material for CCENT exam questions is available for you. Studying material for CCENT certification exams is available for you. Windows operating system is required to check the validity of Cisco 300-410 certification exam questions. The Cisco CCENT exam questions and answers are available for free study. Pass4sures offers the CCENT (300-410) exam certification to the students at lowest cost. The Cisco CCENT (300-410) certification is widely demanded in IT industry. Purchase the best study guide for CCENT exam. CCNA certification is not sufficient to meet the current needs of Networking Industry. Implementing the CCENT certification is the only way to make you more marketable. Guide for CCENT certification is available for you. Valid version of CCENT exam is available for you.
You can prepare for CCENT exam by using the best study material. Requirements of the CCENT certification are available for you, cisco's CCENT certification should be your goal. Features of the CCENT certification are available for you. Passing the CCENT exam is only half the work of getting a job. Best practice are followed to prepare questions for the CCENT exam. Networking exams are updated on regular basis.
Study resources for the Valid 300-410 Braindumps: https://www.pass4sures.top/CCNP-Enterprise/300-410-testking-braindumps.html
Latest CCNP Enterprise 300-410 Actual Free Exam Questions: https://drive.google.com/open?id=1vNb0O35eXjNQvnbLKit9n8DroGB8y164