New 201 Test Materials & Valid 201 Test Engine [Q21-Q36]

New 201 Test Materials & Valid 201 Test Engine

201 Updated Exam Dumps [2022] Practice Valid Exam Dumps Question

NEW QUESTION 21
A BIG-IP Administrator needs to find which modules have been licensed for use on the BIG-IP system. In which section of the Configuration Utility can the BIG-IP Administrator find this information?

• A. System > Support
• B. System > Services
• C. System > Resource Provisioning
• D. System > Platform

Answer: C

 

NEW QUESTION 22
Refer to the exhibit.

Which Pool Members are receiving traffic?

• A. serv1
• B. serv1, serv3, serv4
• C. serv1, serv3
• D. Serv1, serv2,serv3, serv4

Answer: B

 

NEW QUESTION 23
Interface 1.2 on a BIG-IP VE has a status of UNINITIALIZED. What is the reason for this status?

• A. No default route has been created.
• B. Interface 1.2 has been disabled.
• C. Interface 1.2 has been added to a trunk.
• D. Interface 1.2 has NOT been assigned to a VLAN.

Answer: D

Explanation:
trunk is a portchannel, you need to add a physical interface.

 

NEW QUESTION 24
Which parameters are set to the same value when a pair of BIGElIP devices are synchronized.

• A. VLAN failElsafe settings
• B. host names
• C. MAC masquerade addresses
• D. profile definitions
• E. system clocks

Answer: D

 

NEW QUESTION 25
In the BIG-IP Configuration Utility, a user requests a single screen view to determine the status of all Virtual Servers and associated pool members, as well as any iRules in use. Where should the BIG-IP Administrator instruct the user to find this view?

• A. Local Traffic > Network Map
• B. Statistics
• C. Local Traffic > Virtual Servers
• D. Local Traffic > Monitors

Answer: A

Explanation:
Network Map can display vs and its associated pool, pool member, and irule, can be retrieved, and can be quickly linked.

 

NEW QUESTION 26
Assuming other failElover settings are at their default state, what would occur if the failElover cable were to be disconnected for five seconds and then reconnected.

• A. When the cable is disconnected, both systems will become active. When the voltage is restored, both systems will maintain active mode.
• B. When the cable is disconnected, both systems will become active. When the voltage is restored, unit two will revert to standby mode.
• C. Nothing. FailElover due to loss of voltage will not occur if the voltage is lost for less than ten seconds.
• D. As long as network communication is not lost, no change will occur.

Answer: B

 

NEW QUESTION 27
A BIG-IP Administrator sees the following error message in /var/log/ltm diskmonitor: *******; Disk partition shared has less than 30$ free Which section of the Configuration Utility should the BIG-IP Administrator access to investigate this error message?

• A. Statistics > Analytics
• B. System > File Management
• C. System > Disk Management
• D. Statistics > Module Statistics > System

Answer: C

 

NEW QUESTION 28
Active connections to pool members are unevenly distributed. The load balancing method is Least Connections (member) Priority Group Activation is disabled. What is a potential cause of the event distribution?

• A. SSL Profile Server is applied
• B. Priority Group Activation is disabled
• C. Persistence profile is applied
• D. incorrect load balancing method

Answer: C

 

NEW QUESTION 29
Refer to the exhibit.

A BIG-IP Administrator needs to configure health monitors for a newly configured server pool named Pool_B.
Which health monitor settings will ensure that all pool members will be accurately marked as available or unavailable?

• A. HTTPS, HTTP, FTP, and SSH with the Availability Requirement of all health monitors
• B. HTTPS and HTTP with the Availability Requirement of at least one health monitor
• C. HTTPS, HTTP, FTP, and SSH, with the Availability Requirement of at least one monitor
• D. HTTPS, HTTP, FTP, and ICMP, with the Availability Requirement of all health monitors

Answer: C

Explanation:
Explanation
From the port, the four members are HTTP, FTP, HTTPS, and SSH applications. If you want to monitor at the same time, you must configure at least one.

 

NEW QUESTION 30
A VLAN has the following objects configured:
Self-IP 10.10.10.100 with port lockdown set to Allow default
Virtual server 10.10.10.100:443 with UDP profile enabled
Virtual server 10.10.10.0/24 port forwarding virtual server
Global destination NAT forwarding 10.10.10.100 to internal server 172.168.10.100 Which object will process this request when https://10.10.10.100 is entered into a browser?

• A. global destination NAT forwarding 10.10.10.100 to internal server 172.168.10.100
• B. virtual server 10.10.100/24 port o forwarding virtual server
• C. virtual server 10.10.10.100.443 with UDP profile enabled
• D. self-IP 10.10.10.100 with port lockdown set to Allow default

Answer: D

 

NEW QUESTION 31
A BIG-IP Administrator is configuring a pool with members who have differing capabilities. Connections to pool members must be load balanced appropriately.
Which load balancing method should the BIG-IP Administrator use?

• A. Fastest (node)
• B. Least Sessions
• C. Weighted Least Connections (member)
• D. Least Connections (member)

Answer: C

 

NEW QUESTION 32
A BIG-IP Administrator plans to upgrade a BIG-IP device to the latest TMOS version.
Which two tools could the administrator leverage to verify known issues for the target versions?
(Choose two.)

• A. F5 Bug Tracker
• B. FSiHealth
• C. F5 Downloads
• D. F5 University
• E. F5 End User Diagnostics (EUD)

Answer: A,B

Explanation:
Explanation
F5 University -- F5 learning materials
F5 Downloads - iso download page
F5 End User Diagnostics (EUD) -- Hardware detection

 

NEW QUESTION 33
Which VLANs must be enabled for a SNAT to perform as desired (translating only desired packets).

• A. The SNAT must be enabled for the VLANs where desired packets arrive and leave the BIGElIP.
• B. The SNAT must be enabled for all VLANs.
• C. The SNAT must be enabled for the VLANs where desired packets arrive on the BIGElIP.
• D. The SNAT must be enabled for the VLANs where desired packets leave the BIGElIP.

Answer: C

 

NEW QUESTION 34
A site wishes to perform source address translation on packets arriving from the Internet for clients using some pools but not others. The determination is not based on the client's IP address, but on the pool they are load balanced to. What could best accomplish this goal.

• A. A SNAT for all addresses could
  be defined,
  and then disable the SNAT processing for select pools.
• B. For each virtual server, regardless their default load balancing pools, association with SNAT pools could vary dependent upon need.
• C. The decision to perform source address translation is always based on a client's address (or network). Thus, this goal cannot be achieved.
• D. The decision to perform source address translation is always based on VLAN. Thus, the goal cannot be achieved.

Answer: A

 

NEW QUESTION 35
A BIG-IP Administrator makes a configuration change to the BIG-IP device. Which file logs the message regarding the configuration change?

• A. /var/log/audit
• B. /var/log/secure
• C. /var/log/messages
• D. /var/log/user.log

Answer: A

Explanation:
Explanation
About audit logging
Audit logging is an optional feature that togs messages whenever a BIG-IP system object, such as a virtual server or a load balancing pool, is confined (that is. created, modified, or deleted). The BiGIP system logs the messages for these auditing events in the file /var/log'audit There are three ways that objects can be configured
* By user action
* By system action
* By loading configuration data
Whenever an object is configured in one of these ways, the BIG-IP system logs a message to the audit log

 

NEW QUESTION 36
......

F5 201 Exam Syllabus Topics:

Topic	Details
Topic 1	Provide quantitative and relevant information appropriate for a given issues Identify a pool member not in the active priority group
Topic 2	Create and restore a UCS archive under the appropriate circumstances Force an active unit to standby under the appropriate circumstances
Topic 3	Review the Network Map in order to determine the status of objects Identify which modules are licensed and/or provisioned
Topic 4	Identify the appropriate supporting components and severity levels for an F5 support ticket Identify the current configured state of the pool member
Topic 5	Recognize when a packet capture is needed within the context of a performance issue Perform an End User Diagnostic per F5 documentation and collect the output
Topic 6	Given an issue, determine the appropriate severity according to F5 guidelines Identify a possible hardware issue within the log files
Topic 7	Given an HA pair, describe the appropriate strategy for deploying a new software image Use the dashboard to gauge the current running status of the system
Topic 8	Identify which high-level tasks can be automated using BIG-IQ Verify remote connectivity to the BIG-IP in order to determine the cause of a management connectivity issues
Topic 9	Use iApps Analytics to gauge the current running status of application services Identify the reason a virtual server is not working as expected
Topic 10	Identify traffic diverted due to persistence record Use BIG-IP tools in order to identify potential performance issues
Topic 11	Understand the processes of licensing, license reactivation, and license modification (add-ons) Identify the reason a pool member has been marked down by health monitors

How to book the F5-201: TMOS Administration Exam

Register or log in on F5 Network website, or visit the Candidate Portal, or contact F5 Certification for more information.

 

201 Sample with Accurate & Updated Questions: https://www.pass4sures.top/F5Networks/201-testking-braindumps.html

201 Exam Info and Free Practice Test | Pass4sures: https://drive.google.com/open?id=18zksyCR0d1lETNOEimDvSq8JdekK3ORP