Latest [Jun 30, 2026] Cisco 300-425 Exam Practice Test To Gain Brilliante Result
Take a Leap Forward in Your Career by Earning Cisco 300-425
Exam Target Audience
Individuals qualifying for 300-425 exam are specialists who are into the designing of wireless network solutions which the enterprise requires. As a rule, these are network engineers or network analysts. They qualify for this validation only after passing the core exam that stands for Cisco core technologies targeting the network of an enterprise.
NEW QUESTION # 131
An engineer must perform a pre-deployment site survey for a new building in a high-security area. The design must provide a primary signal RSSI of -65 dBm for the clients. Which two requirements complete This design? (Choose two)
- A. Number of clients
- B. WLC model
- C. HAVC access
- D. Site access
- E. AP model
Answer: A,E
Explanation:
For a pre-deployment site survey, it's important to know the AP model to understand the capabilities and coverage pattern of the APs. Additionally, knowing the number of clients helps to design a network that can handle the expected client density.
https://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057-site-survey-guidel
NEW QUESTION # 132
An engineer must perform a predictive wireless survey to indicate the number of access points required. The engineer has created a new project and imported the floor plan. Which step must be taken next for accurate AP placement?
- A. Place the access points.
- B. Analyze the network.
- C. Set the scale.
- D. Identify the coverage area.
Answer: C
NEW QUESTION # 133
An engineer must speed up the reauthentication delays that are being experienced on the wireless infrastructure by deploying a key-caching mechanism. Which mechanism must be configured?
- A. PMF
- B. GTK-randomization
- C. PEAP
- D. FT
Answer: D
Explanation:
NEW QUESTION # 134
An engineer is performing an AP-on-a-stick survey and -nds that the 5 GHz channel overlap is too high when an appropriate number of APs are used for the density requirements. Which two actions during the survey reduce channel overlap? (Choose two.)
- A. Enable power saving mode.
- B. Use directional antennas to limit the coverage area of some APs.
- C. Raise the minimum data rate to 24 Mbps.
- D. Increase AP transmit power to improve the SNR.
- E. Allow the use of UNII-2e channels.
Answer: B,C
Explanation:
Raising the minimum data rate to 24 Mbps will reduce the range at which devices can connect, thereby reducing channel overlap. Using directional antennas can also help limit the coverage area of some APs, which can further reduce channel overlap by focusing the signal in specific directions rather than in a broad coverage pattern. Reference: Designing Cisco Enterprise Wireless Networks (ENWLSD 300-425)
NEW QUESTION # 135
An engineer is designing a wireless network in a historic building that has large rooms and ornate wall coverings Which approach must be considered first when placing access points?
- A. aesthetes
- B. cell overlap
- C. RF coverage
- D. RF interference
Answer: C
NEW QUESTION # 136
An engineer is designing a solution where guests terminate on an anchor controller in the DMZ. The engineer is having issues and wants to test connectivity between members of a mobility group. Which command must be issued to test whether a mobility control packet is able to be reached over the management interface?
- A. mapping
- B. mapping
- C. show logging
- D. tracert
Answer: D
Explanation:
The 'tracert' command is used to test connectivity between members of a mobility group by tracing the path that mobility control packets take over the network. This command helps identify any potential issues with the route that the packets are taking, which could affect the ability of guests to connect to the anchor controller in the DMZ. References := (CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide Premium Edition and Practice)
NEW QUESTION # 137
Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)
- A. spirit level
- B. goggles
- C. access point
- D. PoE battery
- E. tall tripod
- F. ladder
Answer: C,D,E
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/81/design/guide/b_mesh_81/Site_Preparation_and_Planning.html
NEW QUESTION # 138
A network engineer is configuring high availability on an access point. What is the maximum number of controllers that can be configured?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
Explanation:
Explanation
So max 2 will be supported on an AP.
NEW QUESTION # 139
A wireless deployment in a high-density environment is being used by vendors to process credit card payment transactions via handheld mobile scanners. The scanners are having problems roaming between access points in the environment. Which feature on the wireless controller should have been incorporated in the design?
- A. Application Visibility Control
- B. 802.11w
- C. AP Heartbeat Timeout
- D. RX-SOP
Answer: D
Explanation:
Section: Wired and Wireless Infrastructure
NEW QUESTION # 140
A customer has a single anchor WLC named Anchor A. Anchor A is in a DMZ and provides guest access. The customer wants to deploy an additional anchor controller named Anchor B to provide redundancy if Anchor A fails. Which design approach should be taken for the guest WLAN priority on the foreign WLC for each anchor WLC?
- A. Set Anchor A to priority 3 and Anchor B to priority 1.
- B. Set Anchor A to priority 1 and Anchor B to priority 1.
- C. Set Anchor A to priority 1 and Anchor B to priority 3.
- D. Set Anchor A to priority 3 and Anchor B to priority 3.
Answer: C
Explanation:
In a wireless network design where redundancy is required for guest access, setting different priorities for the anchor controllers ensures that one serves as the primary and the other as a backup. Anchor A, being the primary controller, should have a higher priority (lower numerical value), making it the preferred choice for guest WLAN connections. Anchor B, as the secondary or backup controller, should have a lower priority (higher numerical value) so that it is used only if Anchor A fails. This approach provides a failover mechanism for guest access in the DMZ.
NEW QUESTION # 141
An engineer must install an outdoor wireless network for an area with a direct line of sight. The outdoor APs are in an open area with a history of harsh weather. Which two parameters must the engineer consider to prevent an outdoor wireless outage? (Choose two.)
- A. elimination of trees
- B. cable strength
- C. antenna cable grounding
- D. lightning arrestor installation
- E. cable length
Answer: C,D
NEW QUESTION # 142
An engineer must create data-link redundancy for the company's Cisco Wireless LAN Controller. The engineer has decided to configure LAG-based redundancy instead of port-based redundancy. Which three features of LAG-based redundancy influenced this decision? (Choose three.)
- A. All interface traffic passes as long as one port is up.
- B. Full bandwidth of all links is available.
- C. Ports are grouped into multiple LAGs.
- D. The same port has multiple untagged dynamics interfaces.
- E. Packets are always sent out on the same port they are received on.
- F. Interface connection to two separate nonstacked switches is available.
Answer: A,C,E
Explanation:
https://community.cisco.com/t5/wireless-mobility-documents/lag-link-aggregation/ta-p/3128669
NEW QUESTION # 143
Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected?
- A. ping
- B. mping
- C. eping
- D. rping
Answer: A
NEW QUESTION # 144
A wireless engineer is using Ekahau site survey to validate that an existing wireless network is operating as expected, which type of survey should be using to identify the end-to-end network performance?
- A. Passive
- B. Spectrum analysis
- C. GPS assisted
- D. Active ping
Answer: B
Explanation:
https://support.ekahau.com/hc/en-us/articles/115004973067-Spectrum-Analysis-Surveys
NEW QUESTION # 145
Refer to the exhibit.
What is the main reason why the Wi-Fi design engineer took a different approach than installing the APs in the offices, even though that installation provides better coverage?
- A. transmit power considerations
- B. aesthetics
- C. antenna gain
- D. power supply considerations
Answer: A
Explanation:
Explanation
https://www.cisco.com/en/US/docs/solutions/Enterprise/Mobility/emob30dg/RFDesign.html#wp1000551
NEW QUESTION # 146
A network engineer needs to create a wireless design to bridge wired IP surveillance cameras in the parking lot through a mesh AP. To which operate mode of the AP should the cameras connect?
- A. Flexconnect
- B. MAP
- C. Local
- D. RAP
Answer: B
NEW QUESTION # 147
An engineer is performing an AP-on-a-stick survey and finds that the 5 GHz channel overlap is too high when an appropriate number of APs are used for the density requirements. Which two actions during the survey reduce channel overlap? (Choose two.)
- A. Enable power saving mode.
- B. Use directional antennas to limit the coverage area of some APs.
- C. Raise the minimum data rate to 24 Mbps.
- D. Increase AP transmit power to improve the SNR.
- E. Allow the use of UNII-2e channels.
Answer: B,C
Explanation:
Raising the minimum data rate to 24 Mbps will reduce the range at which devices can connect, thereby reducing channel overlap. Using directional antennas can also help limit the coverage area of some APs, which can further reduce channel overlap by focusing the signal in specific directions rather than in a broad coverage pattern. References: Designing Cisco Enterprise Wireless Networks (ENWLSD 300-425)
NEW QUESTION # 148
An engineer must design a predictive site survey. The wireless network must be "location-ready".
Each floor is quite small and has only a few offices. Which approach must be considered?
- A. At least two access points are deployed on each floor
- B. At least four access points are deployed on each floor.
- C. At least three access points are deployed on each floor.
- D. At least one access points are deployed on each floor.
Answer: C
NEW QUESTION # 149
An engineer must create data-link redundancy for the company's Cisco Wireless LAN Controller. The engineer has decided to configure LAG-based redundancy instead of port-based redundancy. Which three features of LAG-based redundancy influenced this decision? (Choose three.)
- A. All interface traffic passes as long as one port is up.
- B. Packets are always sent out on the same port they are received on.
- C. Full bandwidth of all links is available.
- D. Ports are grouped into multiple LAGs.
- E. The same port has multiple untagged dynamics interfaces.
- F. Interface connection to two separate nonstacked switches is available.
Answer: A,C,D
Explanation:
LAG-based redundancy is chosen for its ability to provide continuous connectivity as long as one port in the LAG is operational (B), utilize the full bandwidth capacity of all the links in the LAG (E), and allow for the grouping of ports into multiple LAGs for increased redundancy and bandwidth (F). References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide.
NEW QUESTION # 150
Drag and drop the characteristics from the left onto the correct functionalities on the right.
Answer:
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONS
NEW QUESTION # 151
A wireless engineer is getting ready to perform a predictive site survey. The new network needs to support data and voice over wireless. Which two Cisco recommendations should be considered for the design?
(Choose two.)
- A. Set the cell boundary to -67 dBm.
- B. Use the 5 GHz radio band due to 40 MHz bandwidth capability.
- C. Set the cell overlap to 15%
- D. Set -19 dBm of separation between APs on the same channel.
- E. Use the 5 GHz radio band due to the 24 non-overlapping channels.
Answer: A,B
Explanation:
The 5 GHz band is recommended for voice over wireless due to its wider channel bandwidths, allowing for higher data rates. Setting the cell boundary at -67 dBm ensures sufficient signal strength for reliable voice communication. References: CCNP Enterprise Wireless Design ENWLSD 300-425 Official Cert Guide.
NEW QUESTION # 152
A technician connects a Cisco Aironet 3700 Series access point to a switch and realizes that the AP is coming up with 3x3 MIMO. Which reason explains this behavior?
- A. The switch is 802.3af capable.
- B. The switch is PoE+ capable.
- C. A redundant power supply is unavailable on the switch.
- D. The AP is getting power from a power injector.
Answer: A
Explanation:
NEW QUESTION # 153
A wireless engineer is designing a wireless network for a warehouse using access points with internal antennas. Which two elements have a negative effect on the wireless users? (Choose two.)
- A. access point height
- B. client authentication
- C. wireless channels
- D. absorption
- E. client authorization
Answer: A,D
Explanation:
Explanation
https://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1250-series/design_guide_c07-693245.html#
NEW QUESTION # 154
A wireless engineer is performing a post verification of a wireless network. Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)
- A. The rate of retransmitted packets must be 20 percent or below.
- B. The rate of retransmitted packets must be 15 percent or below.
- C. The coverage area must have a noise floor that does not exceed -87 dBm.
- D. The client device must have at least an -65 dBm RSSI.
- E. The client device must have at least an -67 dBm RSSI.
Answer: D,E
Explanation:
Voice services on a wireless network require a strong and stable signal, as well as low interference and retransmission rates. An RSSI (Received Signal Strength Indicator) of at least -67 dBm is considered the minimum for acceptable voice quality, and -65 dBm is even better, providing a buffer for signal fluctuation. A noise floor of -87 dBm would be too high and could interfere with signal clarity. Retransmission rates should be kept as low as possible; 15% or below is a good target to ensure efficient communication.
NEW QUESTION # 155
An engineer has configured guest anchoring for a newly created SSD however, the mobility tunnels are not up, and EPING is failing from the foreign WLC to the anchor WLC. Which traffic flow must be allowed at the firewall to enable the communication?
- A. UDP port 97
- B. TCP port 97
- C. UDP port 16666
- D. IP protocol 97
Answer: C
Explanation:
NEW QUESTION # 156
......
Authentic Best resources for 300-425 Online Practice Exam: https://www.pass4sures.top/CCNP-Enterprise/300-425-testking-braindumps.html
Updates Up to 365 days On Developing 300-425 Braindumps: https://drive.google.com/open?id=1-XM0r-H_ZVP-FmQGuExKKjwsB2ngM3uk